Calculation program QMSOFT® / QM-GAUGECAL
The calculation program QMSOFT®/QM-GAUGECAL is designed for the computer aided calculation of nominal values and tolerances for fixed gauges. Currently the program does include the following standards:
- GO Plain ring gauges acc. to DIN 7150-2:2007, BS 269:1982, ANSI/ASME B89.1.6M, NF E 02-202
- NO GO ring gauges acc. to DIN 7150-2:2007, BS 269:1982, ANSI/ASME B89.1.6M, NF E 02-202
- Master rings acc. to DIN 2250-1, BS 4064, BS 4065, ANSI/ASME B89.1.6M, NF E 11-011
- GO plain plug gauges acc. to DIN 7150-2:2007, BS 269:1982, ANSI/ASME B89.1.6M, NF E 02-202
- NO GO plain plugs acc. to DIN 7150-2:2007, BS 269:1982, ANSI/ASME B89.1.6M, NF E 02-202
- GO/NO GO plain plug gauges acc. to DIN 7150-2:2007, BS 269:1982, ANSI/ASME B89.1.6M
- GO plain snap gauges acc. to DIN 7150-2:2007
- NO GO plain snap gauges acc. to DIN 7150-2:2007
- GO/NO GO (double sided) plain snap gauges acc. to DIN 7150-2:2007
- Master setting disks (Style 1, 2 and 3) acc. to ANSI/ASME B89.1.6M
- Rod gauges with spherical ends acc. to DIN 7150-2:2007
- Check plugs for snap gauges acc. to DIN 7150-2:2007
- Setting standards for micrometers acc. factory standards
- ISO metric screw threads according to ISO 1502:1996 (DIN ISO 965:1998)
- Unified threads and thread gauges according to ANSI/ASME B1.1-1982/ B1.2-1983
- Gauges for unified threads (ANSI/ASME B1.1-1982) according to BS 919-1:2007
- Gauges for Metric M Screw Threads according to ANSI/ASME B1.16M-1984
- NPSM pipe threads according to ANSI/ASME B1.20.1-1983
- Screw taps according to DIN 802:1982
- Pipe threads and gauges according to ISO 228:2000 (also the older DIN 259:1979)
- Steel conduit threads according to DIN 40431:1972
- ISO metric trapezoidal screw threads according to DIN 103:1997
- Parallel screw threads of Whitworth form according to BS 84:2007 / BS 919-2:2007
- Metrical thread inserts according to DIN 8140:1999 (EG threads)
- HELICOIL threads according to Boellhoff factory standard
- Knuckle threads according to DIN 405:1997
- Buttress threads according to DIN 513:1985 (factory standard for gauge values)
- Threads for valves according to DIN 7756:1979 and ETRTO V.7
- ACME Threads according to ASME / ANSI B 1.5 – 1988
- Stub ACME Threads according to ASME / ANSI B 1.8 – 1988
- Hot-dip galvanised threads according to DIN 965:1999
- Pipe Threads, General purpose (NPT..) according to ANSI/ASME B1.20.1 - 1983
- Pipe Threads where pressure-tight joints are made on the threads acc. to ISO 7-2:2000
- Pipe threads for tubes and fittings according to BS21:1985
- Metric External Taper Screw Threads according to DIN 158
- Gages for Dryseal Pipe Threads (e.g. NPTF..) according to ASME B1.20.5-1991
- Whitworth Pipe threads for threaded pipes and fittings acc. to DIN 2999 – July 1983
After selecting the standard, the type of gauge, (for example: Screw thread GO ring gauge) and entering the gauge designation, for example: M20x1, all of the required gauge nominal values and tolerances will be calculated automatically. The limitations and restrictions of the norms being applied will be indicated. The program supports the nominal value generation and the measurement process for all types of thread gauges being standardized and also for all types of plain gauges used to check the minor or major diameter of screw threads. Results can be produced on the screen and/or the printer and/or in a file. It is possible to customize certificates using the so called "certificate layout files" (templates).
The program can be started up directly from the QMSOFT®/QM-MANAGE gauge data management system. In this case it will receive all necessary nominal data necessary directly from the data base. At the end of the inspection the results and the calibration certificate will automatically be transferred back to the data base program.
|
